diff --git a/0-preinstall.sh b/0-preinstall.sh
index c50a418..8116728 100644
--- a/0-preinstall.sh
+++ b/0-preinstall.sh
@@ -152,10 +152,16 @@ echo "-- Check for low memory systems <8G --"
 echo "--------------------------------------"
 TOTALMEM=$(cat /proc/meminfo | grep -i 'memtotal' | grep -o '[[:digit:]]*')
 if [[  $TOTALMEM -lt 8000000 ]]; then
-    dd if=/dev/zero of=/swapfile bs=1M count=2048 status=progress
-    chmod 600 /swapfile
-    mkswap /swapfile
-    swapon /swapfile
+    #Put swap into the actual system, not into RAM disk, otherwise there is no point in it, it'll cache RAM into RAM. So, /mnt/ everything.
+    mkdir /mnt/opt/swap #make a dir that we can apply NOCOW to to make it btrfs-friendly.
+    chattr +C /mnt/opt/swap #apply NOCOW, btrfs needs that.
+    dd if=/dev/zero of=/mnt/opt/swap/swapfile bs=1M count=2048 status=progress
+    chmod 600 /mnt/opt/swap/swapfile #set permissions.
+    chown root /mnt/opt/swap/swapfile
+    mkswap /mnt/opt/swap/swapfile
+    swapon /mnt/opt/swap/swapfile
+    #The line below is written to /mnt/ but doesn't contain /mnt/, since it's just / for the sysytem itself.
+    echo "/opt/swap/swapfile	none	swap	sw	0	0" >> /mnt/etc/fstab #Add swap to fstab, so it KEEPS working after installation.
 fi
 echo "--------------------------------------"
 echo "--   SYSTEM READY FOR 0-setup       --"
diff --git a/1-setup.sh b/1-setup.sh
index 9be92ec..97b338c 100644
--- a/1-setup.sh
+++ b/1-setup.sh
@@ -20,17 +20,18 @@ echo "Setting up mirrors for optimal download          "
 echo "-------------------------------------------------"
 pacman -S --noconfirm pacman-contrib curl
 pacman -S --noconfirm reflector rsync
-iso=$(curl -4 ifconfig.co/country-iso)
 cp /etc/pacman.d/mirrorlist /etc/pacman.d/mirrorlist.bak
 
 nc=$(grep -c ^processor /proc/cpuinfo)
 echo "You have " $nc" cores."
 echo "-------------------------------------------------"
 echo "Changing the makeflags for "$nc" cores."
+TOTALMEM=$(cat /proc/meminfo | grep -i 'memtotal' | grep -o '[[:digit:]]*')
+if [[  $TOTALMEM -gt 8000000 ]]; then
 sudo sed -i 's/#MAKEFLAGS="-j2"/MAKEFLAGS="-j$nc"/g' /etc/makepkg.conf
 echo "Changing the compression settings for "$nc" cores."
 sudo sed -i 's/COMPRESSXZ=(xz -c -z -)/COMPRESSXZ=(xz -c -T $nc -z -)/g' /etc/makepkg.conf
-
+fi
 echo "-------------------------------------------------"
 echo "       Setup Language to US and set locale       "
 echo "-------------------------------------------------"
@@ -38,7 +39,7 @@ sed -i 's/^#en_US.UTF-8 UTF-8/en_US.UTF-8 UTF-8/' /etc/locale.gen
 locale-gen
 timedatectl --no-ask-password set-timezone America/Chicago
 timedatectl --no-ask-password set-ntp 1
-localectl --no-ask-password set-locale LANG="en_US.UTF-8" LC_COLLATE="" LC_TIME="en_US.UTF-8"
+localectl --no-ask-password set-locale LANG="en_US.UTF-8" LC_TIME="en_US.UTF-8"
 
 # Set keymaps
 localectl --no-ask-password set-keymap us
@@ -145,6 +146,7 @@ PKGS=(
 'networkmanager'
 'nodejs'
 'ntfs-3g'
+'ntp'
 'okular'
 'openbsd-netcat'
 'openssh'
diff --git a/dotfiles/kitty/kitty-themes/README.md b/dotfiles/kitty/kitty-themes/README.md
index 828d603..84ea337 100755
--- a/dotfiles/kitty/kitty-themes/README.md
+++ b/dotfiles/kitty/kitty-themes/README.md
@@ -58,7 +58,7 @@ the previews for each theme in the [section](#previews) below or in this other
 
 ### Conda
 
-If you using the ``conda`` package manager, you may also install these themes
+If you're using the ``conda`` package manager, you may also want to install these themes
 with the following command:
 
 ```bash