Implement host-computed biquad EQ coefficient generation and multi-fragment
bridge writes for the PRO X 2 LIGHTSPEED headset's 5-band parametric EQ.
The coefficient algorithm uses standard Audio EQ Cookbook peaking EQ formulas
with a simplified rescale normalization (max_b0 × 1.19 headroom). This is our
own implementation — not an exact replica of LGHUB's ~350-line per-band cascade
normalization — but it produces functionally correct results. The DSP
compensates via the rescale factor, and the EQ changes are audible and working
on real hardware.
Wire format verified against 38 LGHUB pcap writes:
- 4-byte LE section headers, LE uint16 coefficient words
- Mixed Q1.31/Q2.30 fixed-point with 24-bit precision
- Only b-coefficients divided by rescale; a-coefficients unchanged
- Two sections: 48kHz playback + 16kHz mic
- No trailing padding, no extra words between sections
Changes:
- base.py: Add flags parameter to write_centurion_cpl() for multi-fragment CPL
- device.py: Rewrite multi-fragment bridge send — proper CPL fragmentation with
fragment 0 carrying bridge prefix/hdr and continuations carrying raw sub_msg,
all fragments sent back-to-back without intermediate ACKs
- hidpp20.py: Replace placeholder coefficient code with full biquad math,
mixed Q-format quantization, rescale normalization, and dual-section output
- settings_templates.py: Persist EQ to slot 0x80 after writing to slot 0x00
so settings survive power cycle
- tests: Update expected SetEQParameters payloads for new coefficient format
Replace ad-hoc heuristics with proper bridge event function dispatch:
- Function 0 (ConnectionStateChangedEvent): parse sub-device list length
to determine connect (len>0) vs disconnect (len=0)
- Function 1 (MessageEvent): fallback online detection if headset sends
a message while marked offline (handles cold-start power-on)
Remove CPL sub_id>=0x80 fallback in listener that misidentified HID++
error replies as disconnect events. Skip HID++ 1.0
set_configuration_pending_flags for CenturionReceiver (not supported).
Also adds OnboardEQ (0x0636) support, bridge multi-fragment sends,
bridge-based headset ping probe, and CLI offline display.
- Add signed int8 support to RangeValidator for HeadsetMicGain (0x0611)
- Make HeadsetSidetone version-aware: v1 uses 2-byte skip, v2+ uses
3-byte skip with 0xFF separator per protocol spec
- Fix ruff formatting in device.py, listener.py, udev_impl.py
- Update CenturionReceiver test for renamed receiver
- Add CenturionReceiver class that provides the Receiver UI interface so
the dongle appears as a parent with the headset indented underneath,
matching how Lightspeed/Unifying receivers display
- Independently probe dongle features via feature_request() on the
CenturionReceiver, separate from headset features via bridge
- Fix bridge notification dispatch: remove incorrect sub_cpl=0xFF filter
that was silently dropping all battery and other notifications
- Fix battery status decoding: charging status is at byte 2 (not byte 1)
of the CENTURION_BATTERY_SOC response
- Detect wired vs wireless by checking for CentPPBridge in discovered
features; wired headsets fall back to standalone Device
- Name the dongle "Centurion Receiver" to distinguish from the headset
- Filter unprintable dongle serial (control characters 0x14-0x1F)
- Update CLI show output with proper receiver/child hierarchy and spacing
Replace the hardcoded descriptor entry with dynamic discovery of all device
properties via the Centurion protocol. The headset name, kind, serial,
firmware, and battery are now probed at runtime — matching how the device
actually presents itself rather than relying on static data.
Key changes:
- Discover sub-device features via CentPPBridge and route requests through
the bridge automatically
- Infer device kind from feature IDs (0x06xx = headset) for both wireless
and direct USB connections
- Read device name from USB product string with protocol probe fallback
- Parse bridge error responses (sub_feat_idx=0xFF) instead of timing out
- Handle unknown HID++ error codes gracefully in base.py
- Fix firmware deduplication for Centurion parent devices
- Prefer sub-device serial/firmware over parent (non-printable) values
- Add Centurion-aware display in solaar show with parent/sub-device sections
- Support both wireless (0AF7 dongle) and direct USB (0AF8) connections
Adds support for the Logitech PRO X 2 LIGHTSPEED Gaming Headset (PID 0x0AF7)
which uses the Centurion transport protocol (report ID 0x51 on USB usage page
0xFFA0) instead of standard HID++ report IDs.
Changes:
- HID enumeration: detect Centurion devices via report descriptor parsing
(usage page 0xFFA0, report ID 0x51, 63-byte frames)
- Centurion transport: wrap/unwrap HID++ 2.0 frames in Centurion framing
for write, read, and ping operations
- Feature discovery: enumerate features individually on Centurion devices
(different response format: [remaining_count, feat_hi, feat_lo])
- Device descriptor for PRO X 2 LIGHTSPEED Gaming Headset
- New feature enum entries for Centurion-era headset features (0x06xx)
- CenturionRawRW class for write-only headset settings controlled via
raw Centurion commands reverse-engineered from HeadsetControl
- HeadsetSidetone setting (0-100 range, persisted locally)
Known limitations:
- Only sidetone control is implemented; other features need RE work
- Settings are write-only (no read-back from device)
- Headset features (0x06xx) not discoverable via IRoot; registered manually
* battery: Extract battery level estimation into function
Test battery level estimation with sharp edges based on predefined
steps. Rename variable for clarity and add type hints.
Related #2744
* battery: Interpolate battery level for some rechargeable devices in percent
Estimate remaining battery based on measured battery voltage. Use linear
interpolation to achieve a smooth line instead of 10 percent jumps.
Fixes#2744
Refactor get_receiver_info. Replacing data structure of known receivers
to avoid for loop, when an efficient dictionary lookup is possible.
Related #2273
* refactoring(logitech_receiver/notifications): change to enums PairingError and BoltPairingError
* refactoring(logitech_receiver/notifications): change to enums PairingError and BoltPairingError (Fix pre-commit checks)
* refactor(logitech_receiver/base.py): create unit tests for ping function before replacing ERRORNamedInts by IntEnum
* refactor(logitech_receiver/base.py): create unit tests for request function before replacing ERROR NamedInts by IntEnum
* refactor(logitech_receiver/base.py): create unit tests for ping function before replacing ERRORNamedInts by IntEnum (add exclusion for macOS)
* refactor(logitech_receiver/base.py): create unit tests for ping function before replacing ERRORNamedInts by IntEnum (fix for python < 3.10)
* refactor(solaar/cli./probe.py): create unit tests for run function before replacing ERROR NamedInts by IntEnum (focusing on the call order when receiving errors)
* refactor(solaar/cli./probe.py): refactor register processing to handle short and long registers in a single loop structure for improved readability and reduced code duplication.
* refactor(logitech_receiver/hidpp10_constants.py): replace ERROR NamedInt by IntEnum.
* refactor(logitech_receiver/hidpp10_constants.py): distinguish hidpp10 and hidpp20 errors in the code for readibility.
* refactor(logitech_receiver/hidpp20_constants.py): replace ERROR NamedInt by IntEnum.
* refactor(logitech_receiver/hidpp20_constants.py): replace ERROR NamedInt by IntEnum. (fix problem with | operator when typing with python 3.8)
* feature(hide on startup option): Visual test (not binded yet) DRAFT
* refactor(solaar/cli./probe.py): create unit tests for run function before replacing ERROR NamedInts by IntEnum (focusing on the call order when receiving errors)
* refactor(solaar/cli./probe.py): refactor register processing to handle short and long registers in a single loop structure for improved readability and reduced code duplication.
* refactor(logitech_receiver/hidpp10_constants.py): replace ERROR NamedInt by IntEnum.
* refactor(logitech_receiver/hidpp20_constants.py): replace ERROR NamedInt by IntEnum.
* refactor(logitech_receiver/hidpp20_constants.py): replace ERROR NamedInt by IntEnum. (fix problem with | operator when typing with python 3.8)
* feature(hide on startup option): Visual test (not binded yet) DRAFT
* Merge: Refactor: hidpp20 to use enum
* Merge: Refactor: hidpp20 to use enum (fix test)
---------
Co-authored-by: some_developer <some.developper.44@gmail.com>
* Remove duplicated Param definition
Use constants from hidpp20 constants
Related #2273
* hidpp20/Param: Refactor to use IntEnum
Related #2273
* hidpp20_constants: Refactor to use IntEnum
Related #2273
* Refactor: test_named_ints_flag_names
Shorten test and clarify behavior using binary numbers.
* Introduce plain flag_names function
This replicates the NamedInts functionality as plain function.
* Refactor FeatureFlag to use IntFlag
Replace NamedInts implementation with IntFlag enum and plain flag_names
function.
Related #2273
* Refactor FirmwareKind to use IntEnum
- Move general FirmwareKind to common module.
- Replace NamedInts implementation with IntEnum.
- Harden related HIDPP 1.0 get_firmware test.
Related #2273
* Refactor CID_GROUP, CID_GROUP_BIT to use IntEnum
Related #2273
* refactoring(logitech_receiver/notifications): change to enums PairingError and BoltPairingError
* refactoring(logitech_receiver/notifications): change to enums PairingError and BoltPairingError (Fix pre-commit checks)
* refactor(logitech_receiver/base.py): create unit tests for ping function before replacing ERRORNamedInts by IntEnum
* refactor(logitech_receiver/base.py): create unit tests for request function before replacing ERROR NamedInts by IntEnum
* refactor(logitech_receiver/base.py): create unit tests for ping function before replacing ERRORNamedInts by IntEnum (add exclusion for macOS)
* refactor(logitech_receiver/base.py): create unit tests for ping function before replacing ERRORNamedInts by IntEnum (fix for python < 3.10)
Ken Sanislo
Peter F. Patel-Schneider
MattHag
Romain Loutrel