Solaar/docs/devices/Wireless Illuminated Keyboa...

68 lines
2.9 KiB
Plaintext

2: Wireless Illuminated Keyboard K800
Codename : K800
Kind : keyboard
Wireless PID : 2010
Protocol : HID++ 1.0
Polling rate : 20 ms (50Hz)
Serial number: FFC65665
Firmware: 22.01.B0019
Bootloader: 02.01
Other: 00.07
The power switch is located on the top right corner.
Notifications: battery status (0x100000).
Battery: full, discharging.
# 0x00 - Enabled Notifications. rw (see HID++ 1.0 spec)
<< ( 0.055) [10 02 8100 000000] '\x10\x02\x81\x00\x00\x00\x00'
>> ( 0.084) [10 02 8100 000000] '\x10\x02\x81\x00\x00\x00\x00'
# 0x01 - Keyboard hand detection. rw, last param is 00 when hand detection is
# enabled, 30 when disabled. (when enabled, keyboard will light up if not
# already when hovering over the front)
<< ( 1.085) [10 02 8101 000000] '\x10\x02\x81\x01\x00\x00\x00'
>> ( 1.114) [10 02 8101 000000] '\x10\x02\x81\x01\x00\x00\x00'
# 0x07 - Battery status (3 = one bar; 1 = red/critical; 5=two bars; 7=three
# bars/full. Second returned param is 25 when keyboard is charging )
<< ( 7.327) [10 02 8107 000000] '\x10\x02\x81\x07\x00\x00\x00'
>> ( 7.368) [10 02 8107 030000] '\x10\x02\x81\x07\x03\x00\x00'
# 0x09 - F key function. rw (read: status, set/get: 00 01 00 means swap
# functions, 00 00 00 means do not swap functions)
<< ( 9.411) [10 02 8109 000000] '\x10\x02\x81\t\x00\x00\x00'
>> ( 9.440) [10 02 8109 000000] '\x10\x02\x81\t\x00\x00\x00'
# 0x17 - Illumination info r/w. Last param: 02 to disable backlight, 01 to
# enable backlight
<< ( 24.965) [10 02 8117 000000] '\x10\x02\x81\x17\x00\x00\x00'
>> ( 24.988) [10 02 8117 3C0001] '\x10\x02\x81\x17<\x00\x01'
# 0x51 - ?
<< ( 99.294) [10 02 8151 000000] '\x10\x02\x81Q\x00\x00\x00'
>> ( 99.543) [10 02 8151 000000] '\x10\x02\x81Q\x00\x00\x00'
# 0x54 - ?
<< ( 103.046) [10 02 8154 000000] '\x10\x02\x81T\x00\x00\x00'
>> ( 103.295) [10 02 8154 FF0000] '\x10\x02\x81T\xff\x00\x00'
# 0xD0 - ?
<< ( 253.860) [10 02 81D0 000000] '\x10\x02\x81\xd0\x00\x00\x00'
>> ( 253.883) [10 02 81D0 000000] '\x10\x02\x81\xd0\x00\x00\x00'
# 0xF1 - Version info (params 0n 00 00 where n is 1..4)
<< ( 289.991) [10 02 81F1 000000] '\x10\x02\x81\xf1\x00\x00\x00'
>> ( 290.032) [10 02 8F81 F10300] '\x10\x02\x8f\x81\xf1\x03\x00'
# 0xF3 - ?
<< ( 292.075) [10 02 81F3 000000] '\x10\x02\x81\xf3\x00\x00\x00'
>> ( 292.116) [10 02 81F3 000000] '\x10\x02\x81\xf3\x00\x00\x00'
# 0x0F - This changes, the last commented line was observed in an earlier run
<< ( 17.728) [10 02 830F 000000] '\x10\x02\x83\x0f\x00\x00\x00'
>> ( 17.976) [11 02 830F FFFB00000240025C000000000FF90080] '\x11\x02\x83\x0f\xff\xfb\x00\x00\x02@\x02\\\x00\x00\x00\x00\x0f\xf9\x00\x80'
#>> ( 17.999) [11 02 830F FFFC007F0243025D000000000FF60080] '\x11\x02\x83\x0f\xff\xfc\x00\x7f\x02C\x02]\x00\x00\x00\x00\x0f\xf6\x00\x80'
# See also https://git.lekensteyn.nl/ltunify/tree/registers.txt for a verbose
# meaning of registers and params.