* Add CLI --slot unpair for Lightspeed receivers
Adds Receiver.force_unpair_slot(), a low-level method that writes the
RECEIVER_PAIRING unpair register (action 0x03) for a given slot regardless
of cache state, bypassing may_unpair and re_pairs gates. Intended for
clearing stale pairings on Lightspeed receivers where Solaar cannot read
the slot's pairing info or the device is no longer reachable on RF.
Extends the `solaar unpair` CLI with three new flags:
--receiver <name> select which receiver to target
--slot <N> target a specific slot number directly
--dry-run print what would happen without issuing the write
The --slot path is gated to Lightspeed receivers only (by receiver_kind)
so Unifying/Bolt/Nano behavior is unchanged. It populates the cache first
and prints the current slot contents so the user can confirm what is
about to be cleared, but does not refuse based on active/offline state —
the explicit --slot N is treated as sufficient intent.
Verified end-to-end on a C547 dual-slot Lightspeed receiver: stale slot
cleared, RECEIVER_INFO sub-registers 0x21/0x31 went to None, connection
count register dropped from 2 to 1, running solaar daemon picked up the
change in real time via the existing DJ pairing notification hook.
Covered by 5 unit tests against a mocked Receiver: empty slot, stale
sentinel, active device invalidation, register write failure, closed
handle.
* Enable GUI unpair for Lightspeed receivers
Flip _lightspeed_receiver() to may_unpair: True so the GUI unpair button
becomes sensitive for Lightspeed-paired devices, and route the GUI unpair
action through _unpair_device(n, force=True) so the unpair register write
actually fires instead of short-circuiting to cache invalidation.
The previous GUI path called `del receiver[n]`, which dispatches to
Receiver.__delitem__ → _unpair_device(n, force=False). On receivers with
re_pairs=True (Lightspeed, Nano) that hits the cache-invalidation branch
at receiver.py:391 and never writes the unpair register — a "fake unpair"
that would have left the slot bound on the hardware even after the button
was enabled.
With force=True, the GUI now issues RECEIVER_PAIRING action 0x03 for the
selected slot, matching the CLI unpair path (cli/unpair.py:39) which has
always used force=True. Lightspeed and Unifying unpair behavior are now
symmetric: the button is enabled, the confirmation dialog is shown, and
the register write is performed.
The pair/add flow is untouched: it still uses set_lock(device=0) which
lets the receiver firmware pick an empty slot, re_pairs remains True so
the listener's silent-replace branch continues to handle re-pair into an
occupied devnumber. Verified on dual-slot C547 hardware that pairing into
an empty slot preserves the occupant of the other slot.
Stale pairings where Solaar can't enumerate the slot (no cached device
row to right-click) still require the --slot CLI from the preceding
commit — that path is orthogonal to this GUI enablement.
* Apply suggestion from @pfps
Lightspeed receivers don't appear to re-pair.
---------
Co-authored-by: Peter F. Patel-Schneider <pfpschneider@gmail.com>
* Handle composite IntFlag.name on Python < 3.11
On Python < 3.11, IntFlag.name returns None for composite flags
(e.g. NotificationFlag(0x000900) = SOFTWARE_PRESENT|WIRELESS).
The previous fix (#3184) returns an empty list in this case, losing
the flag names. This commit decomposes composite flags manually by
iterating over enum members, producing correct results on all
supported Python versions (>= 3.8 as declared in setup.py).
Add regression tests covering composite flags and None input.
Tested on:
- Python 3.9.2 (Debian 11): 56/56 passed
- Python 3.11.15 (pyenv): 56/56 passed
Refs #3184
* Fix line length style violation (E501)
Move comment above the parametrize entry to stay under 127 chars.
---------
Co-authored-by: avercelli <avercelli@vulog.com>
* Treat empty hidraw read as device removal (EOF)
When select() reports a hidraw fd as readable but os.read() returns
empty bytes, that's EOF per POSIX — the device has been removed.
Previously this was silently treated as no data, causing the listener
to loop indefinitely on a gone device instead of cleaning up.
* Fix test_ping_errors missing mocks for _read_input_buffer and write
The test was not mocking _read_input_buffer or write, so ping() would
call into real hidapi.read() with a fake handle (fd 1). The empty-read
EOF detection added in the previous commit made this consistently fail
by raising OSError → NoReceiver before reaching the mocked _read path.
Add the same mocks used by the adjacent test_request_errors.
---------
Co-authored-by: Peter F. Patel-Schneider <pfpschneider@gmail.com>
* Add Centurion transport and PRO X 2 LIGHTSPEED headset support
Adds support for the Logitech PRO X 2 LIGHTSPEED Gaming Headset (PID 0x0AF7)
which uses the Centurion transport protocol (report ID 0x51 on USB usage page
0xFFA0) instead of standard HID++ report IDs.
Changes:
- HID enumeration: detect Centurion devices via report descriptor parsing
(usage page 0xFFA0, report ID 0x51, 63-byte frames)
- Centurion transport: wrap/unwrap HID++ 2.0 frames in Centurion framing
for write, read, and ping operations
- Feature discovery: enumerate features individually on Centurion devices
(different response format: [remaining_count, feat_hi, feat_lo])
- Device descriptor for PRO X 2 LIGHTSPEED Gaming Headset
- New feature enum entries for Centurion-era headset features (0x06xx)
- CenturionRawRW class for write-only headset settings controlled via
raw Centurion commands reverse-engineered from HeadsetControl
- HeadsetSidetone setting (0-100 range, persisted locally)
Known limitations:
- Only sidetone control is implemented; other features need RE work
- Settings are write-only (no read-back from device)
- Headset features (0x06xx) not discoverable via IRoot; registered manually
* Remove static PRO X 2 descriptor; fully probe Centurion devices at runtime
Replace the hardcoded descriptor entry with dynamic discovery of all device
properties via the Centurion protocol. The headset name, kind, serial,
firmware, and battery are now probed at runtime — matching how the device
actually presents itself rather than relying on static data.
Key changes:
- Discover sub-device features via CentPPBridge and route requests through
the bridge automatically
- Infer device kind from feature IDs (0x06xx = headset) for both wireless
and direct USB connections
- Read device name from USB product string with protocol probe fallback
- Parse bridge error responses (sub_feat_idx=0xFF) instead of timing out
- Handle unknown HID++ error codes gracefully in base.py
- Fix firmware deduplication for Centurion parent devices
- Prefer sub-device serial/firmware over parent (non-printable) values
- Add Centurion-aware display in solaar show with parent/sub-device sections
- Support both wireless (0AF7 dongle) and direct USB (0AF8) connections
* Display Centurion dongle as receiver with headset as child device
- Add CenturionReceiver class that provides the Receiver UI interface so
the dongle appears as a parent with the headset indented underneath,
matching how Lightspeed/Unifying receivers display
- Independently probe dongle features via feature_request() on the
CenturionReceiver, separate from headset features via bridge
- Fix bridge notification dispatch: remove incorrect sub_cpl=0xFF filter
that was silently dropping all battery and other notifications
- Fix battery status decoding: charging status is at byte 2 (not byte 1)
of the CENTURION_BATTERY_SOC response
- Detect wired vs wireless by checking for CentPPBridge in discovered
features; wired headsets fall back to standalone Device
- Name the dongle "Centurion Receiver" to distinguish from the headset
- Filter unprintable dongle serial (control characters 0x14-0x1F)
- Update CLI show output with proper receiver/child hierarchy and spacing
* Fix headset setting validators and code formatting
- Add signed int8 support to RangeValidator for HeadsetMicGain (0x0611)
- Make HeadsetSidetone version-aware: v1 uses 2-byte skip, v2+ uses
3-byte skip with 0xFF separator per protocol spec
- Fix ruff formatting in device.py, listener.py, udev_impl.py
- Update CenturionReceiver test for renamed receiver
* Use ConnectionStateChangedEvent for headset online/offline detection
Replace ad-hoc heuristics with proper bridge event function dispatch:
- Function 0 (ConnectionStateChangedEvent): parse sub-device list length
to determine connect (len>0) vs disconnect (len=0)
- Function 1 (MessageEvent): fallback online detection if headset sends
a message while marked offline (handles cold-start power-on)
Remove CPL sub_id>=0x80 fallback in listener that misidentified HID++
error replies as disconnect events. Skip HID++ 1.0
set_configuration_pending_flags for CenturionReceiver (not supported).
Also adds OnboardEQ (0x0636) support, bridge multi-fragment sends,
bridge-based headset ping probe, and CLI offline display.
* Update PRO X 2 LIGHTSPEED device doc with current solaar show output
* Fix Centurion protocol version display (1.16 not 2.6)
The HID++ ping math (major + minor/10.0) produced a bogus "2.6" for
Centurion devices whose ProtocolCapabilities returns major=1, minor=0x10.
Store the raw (major, minor) bytes from the ping response and display
them correctly as "Centurion 1.16" in both CLI and GUI.
* Add OnboardEQ (0x0636) support for Centurion headsets
Implement host-computed biquad EQ coefficient generation and multi-fragment
bridge writes for the PRO X 2 LIGHTSPEED headset's 5-band parametric EQ.
The coefficient algorithm uses standard Audio EQ Cookbook peaking EQ formulas
with a simplified rescale normalization (max_b0 × 1.19 headroom). This is our
own implementation — not an exact replica of LGHUB's ~350-line per-band cascade
normalization — but it produces functionally correct results. The DSP
compensates via the rescale factor, and the EQ changes are audible and working
on real hardware.
Wire format verified against 38 LGHUB pcap writes:
- 4-byte LE section headers, LE uint16 coefficient words
- Mixed Q1.31/Q2.30 fixed-point with 24-bit precision
- Only b-coefficients divided by rescale; a-coefficients unchanged
- Two sections: 48kHz playback + 16kHz mic
- No trailing padding, no extra words between sections
Changes:
- base.py: Add flags parameter to write_centurion_cpl() for multi-fragment CPL
- device.py: Rewrite multi-fragment bridge send — proper CPL fragmentation with
fragment 0 carrying bridge prefix/hdr and continuations carrying raw sub_msg,
all fragments sent back-to-back without intermediate ACKs
- hidpp20.py: Replace placeholder coefficient code with full biquad math,
mixed Q-format quantization, rescale normalization, and dual-section output
- settings_templates.py: Persist EQ to slot 0x80 after writing to slot 0x00
so settings survive power cycle
- tests: Update expected SetEQParameters payloads for new coefficient format
* Extract Centurion protocol into separate modules
Move CenturionReceiver class, factory function, and Centurion protocol
queries (firmware, serial, hardware info, battery, name) from device.py
and hidpp20.py into new centurion.py module. Move OnboardEQ biquad math
and payload builders from hidpp20.py into new onboard_eq.py module.
Move _read_usb_product_string() to common.py to avoid circular imports.
Re-exports preserve backward compatibility for all existing callers.
* Add vertical graphic EQ slider widget for headset equalizer
Replace horizontal slider rows with a traditional graphic EQ layout
using vertical sliders side-by-side, with dB value display and
frequency labels per band.
* Fix device online state clobbered by debug ping in _status_changed
The INFO-level logging guard in _status_changed() called device.ping()
before logging, purely to show accurate online status. But ping() has
side effects — it sets device.online based on the result. When a
ConnectionStateChangedEvent correctly marked a device online, the
subsequent _status_changed() callback would re-ping. If the device
wasn't ready yet (e.g. Centurion headset still booting), the ping
timed out and set online back to False, requiring 2-3 power cycles
to sync state.
Remove the unnecessary ping — the log message already reads
device.online which reflects the state set by the event handler.
* Sort feature constants by ID and add PROFILE_MANAGEMENT
Move RPM_INDICATOR/RPM_LED_PATTERN (0x807A-B) before PER_KEY_LIGHTING
(0x8080-81), sort five Centurion-era headset entries into their correct
positions by feature ID, and add missing PROFILE_MANAGEMENT = 0x8101.
* Add CenturionCoreFeature enum for colliding feature IDs
Centurion transport reuses HID++ 2.0 feature IDs 0x0000, 0x0001,
0x0003, 0x0005, 0x0007 with different meanings. Since SupportedFeature
(IntEnum) requires unique values, create a separate CenturionCoreFeature
enum and resolve_feature() helper for transport-aware lookup.
Also replace the +0x100 offset hack in FeaturesArray.inverse with a
dedicated sub_inverse dict for sub-device feature indexing.
* Fix ruff I001 import sorting in centurion.py and hidpp20.py
* Add 9 missing centurion/headset feature names
Add feature constants split out from the HID++ 2.0 names PR (#3153):
CENTURION_LED_BRIGHTNESS (0x0110), CENTURION_EU_POWER_MODE (0x0115),
CENTURION_DEVICE_BOOL_STATE (0x0116), HEADSET_ADVANCED_PARA_EQ (0x020D),
HEADSET_MIC_TEST (0x020E), HEADSET_EQ_STYLES (0x0213),
BT_HOST_INFO (0x0305), LIGHTSPEED_PAIRING (0x0309),
BT_GAMING_MODE (0x030A).
* Extract _record_ping_protocol helper so all ping paths capture Centurion version
The raw Centurion (major, minor) pickup was only in the Centurion-child
dongle branch of Device.ping(). Wired Centurion variants (e.g. PRO X 2
LIGHTSPEED 046d:0AF8) go through the generic fallback branch and never
recorded the raw version, so they displayed "Centurion 2.6" instead of
"Centurion 1.16".
Extract the protocol + centurion version recording into a helper and
call it from both branches.
---------
Co-authored-by: Peter F. Patel-Schneider <pfpschneider@gmail.com>
flag_names() crashes with AttributeError when NotificationFlag returns
a value whose .name attribute is None. This occurs with certain receiver
firmware versions (Nano C52F, Unifying C52B, Bolt C548).
Return an empty list instead, consistent with the List[str] return type.
Fixes#3184
Co-authored-by: avercelli <avercelli@vulog.com>
* feat: PRO X 2 Superstrike support with click haptics, actuation point and rapid trigger config support
* feat: PRO X 2 Superstrike docs
* docs: document PRO X 2 Superstrike features, device entry, and capabilities
* fix: code review points
# Conflicts:
# lib/logitech_receiver/hidpp20_constants.py
* Fix the write_key_value for dpi_extended
I was playing with the branch from the MR and I wanted to fix the cli stuff, it now properly sets when I use:
solaar config 1 dpi_extended X 400
Should be enough
Signed-off-by: Shane Fagan <mail@shanefagan.com>
* Fix ruff style check
---------
Signed-off-by: Shane Fagan <mail@shanefagan.com>
Co-authored-by: Shane Fagan <mail@shanefagan.com>
* Bulgarian PO files
Български превод на приложението
* Delete bg.mo
* Delete bg.po
* Delete bg.po~
* Bulgarian Translation
Български превод на приложението.
* Update i18n.md
* Delete po/bg.mo
* Delete po/bg.po~
* Add installation guide for Solaar on RHEL 10
Document steps to install and run Solaar on RHEL 10, including environment setup and troubleshooting.
* Add interactive RHEL installer script
Replace scripts=glob("bin/*") with entry_points console_scripts
to make solaar installable via pipx. pipx requires packages to
define console_scripts entry points to detect command-line apps.
* Skip Logitech webcams (PID 0x0800 to 0x09FF) to prevent them from locking up during hidpp checks #3145
* Skip Logitech webcams (PID 0x0800 to 0x09FF) to prevent them from locking up during hidpp checks #3145 - format comment
* Skip Logitech webcams (PID 0x0800 to 0x09FF) to prevent them from locking up during hidpp checks #3145 - format hex
* Skip Logitech webcams from hidpp checks #3145 - local constant for LOGITECH_VENDOR_ID as per code review
Peter F. Patel-Schneider
Ken Sanislo
Alessio85
Caio Quirino da Silva
Nikolay Yordanov
Grant Scott Turner
gnotree ✟🕊︎
Br1an67
Niko Savola
Din Tort
NaviMen
aasami
Mário Victor Ribeiro Silva
daviddavid
Ekaterine Papava